6 Simple tips caring for an industrial sewing machine

6 Simple tips caring for an industrial sewing machine

Anyone starts an industrial sewing machine mission and he must a more get knowledge about it. When you start a new sewing project, the least you need is a broken sewing machine. Keeping equipment clean and well oiled is a great way to practice servicing sewing equipment without involving a craftsman and at the same time extend the life of your workhorse. Below we have put together six simple but important tips for keeping your machine in top working condition. It doesn’t matter if you work in an industrial sewing machine factory, in an atelier or in your own workshop – the principles of caring for sewing equipment are the same everywhere, the only difference is the frequency of service.

Tip # 1

Use a dust cover. It is very easy! Even if you work on your industrial sewing machine every day, it will not be superfluous to cover it with a soft cover during downtime. It’s like using a garage for a car. A dust cover is a very simple way to prevent unwanted dust from entering the equipment body and into the mechanisms.

Tip # 2

Keep your shuttle device clean. This is a really easy way to avoid the pile-up and possible stitch industrial sewing machine quality problems. Simply tilt the sewing machine’s head onto the holder and inspect the shuttle for a pile and a thread trimmer. Be sure to wipe the bobbin case and remove any dirt that accumulates over time. You will be surprised how much garbage can be collected in such a small place. Take a fleecy brush and clean the bobbin case and surrounding area. The main thing is not to remove the grease, it is necessary for the proper operation of the device.

Fashion technology is not only changed the way we perceive our everyday social lives. Even the professional aspects have witnessed a great tremendous transformation

Tip # 3

Remember the industrial sewing machine to change grease. There is much debate about how often it is necessary to change the oil in the car and which oil to use at all. In any case, you should not use WD-40 multi-purpose grease and any engine oils, otherwise, you will have problems. Use only special silicone oils for sewing equipment. For shuttle stitch sewing machines, an oil with a viscosity of 20 mm² / s is required, for a chain stitch industrial sewing machine with a viscosity of 22-24 mm² / s.

Empirically, we also derived the optimal formula for the oil change frequency for industrial sewing machines – 1/6 / 6.

If you just purchased industrial sewing machine equipment, you need to run it at idle for 10-15 minutes, first, fill all the complete oil in the crankcase. After a month of operating the equipment, this oil should be completely drained and replaced with a new one, followed by a replacement of the lubricating fluid every six months. The same applies to industrial over locks and sewing machines, with the only difference being that this equipment also requires industrial sewing machine cleaning and periodic replacement of the oil filter. Also do not forget from time to time to monitor the amount of oil in the crankcase. Typically, for these purposes, there are markings in the sump with indications of a sufficient and low oil level.

Tip # 4

Practice manual lubrication. For industrial sewing machine with double and triple transport of material, some of the components of the upper movement mechanism are located outside the case. To lubricate parts of the external hinges, wicks are usually laid, through which oil comes from a grease fitting located directly in the head of the sewing machine. However, lubricant supply is not provided for the most remote areas, therefore, in practice, in addition to the wick lubricant, manual drip lubrication industrial sewing machine is also practiced. For this purpose, special holes for applying grease are provided on the joints. The manufacturer recommends applying one or two drops of oil to each hole before starting work if the sewing machine is used in the factory. For less intensive work in a small workshop or workshop,

Tip # 5

Keep your grease clean. Each time, at the very beginning of the working session industrial sewing machine wiki, check the absence of foreign objects in the oil sump, such as threads and fabric trimmings. The nozzles of the oil pump are quite narrow, so they can easily clog when sewing debris gets inside the oil intake, and stopping the oil supply to the friction units can lead to more serious problems than just breaking the oil pump. Also, pay attention to the appearance and color of the oil. Pile, dust and metal chips accumulate over time in the lubricant, which can lead to a change industrial sewing machine in the density of the lubricant and the loss of anti-wear and anti-corrosion properties. If the oil has become brown or heavily contaminated, it may be necessary to change it even before the due date.

Tip # 6

Use the magnet correctly industrial sewing machine. It is always fun to watch when a seamstress uses this simple item for other purposes. Often it can be seen on the body of the sewing machine, where it is used as a needle bed. In fact, a magnet is needed to pick up metal objects that could accidentally get into the crankcase and damage the oil pump. To prevent such excesses, the magnet is placed in an oil pan, industrial sewing machine directly in the lubricant and as close to the oil intake as possible.

Leave a Reply

Your email address will not be published.